Free 2V0-41.23 Exam Braindumps

Which table on an ESXi host is used to determine the location of a particular workload for a frame-forwarding decision?

1. A. TEP Table
2. B. MAC Table
3. C. ARP Table
4. D. Routing Table

Correct Answer: B
The MAC table on an ESXi host is used to determine the location of a particular workload for a
frame-forwarding decision. The MAC table maps the MAC addresses of the workloads to their corresponding tunnel endpoint (TEP) IP addresses. The TEP IP address identifies the ESXi host where the workload resides. The MAC table is populated by learning the source MAC addresses of the incoming frames from the workloads. The MAC table is also synchronized with other ESXi hosts in the same transport zone by using the NSX Controller.
https://nsx.techzone.vmware.com/resource/nsx-reference-design-guide

A customer is preparing to deploy a VMware Kubernetes solution in an NSX environment. What is the minimum MTU size for the UPLINK profile?

1. A. 1500
2. B. 1550
3. C. 1700
4. D. 1650

Correct Answer: C
The minimum MTU size for the UPLINK profile is 1700 bytes. This is because the UPLINK profile is used to configure the physical NICs that connect to the NSX-T overlay network. The overlay network uses geneve encapsulation, which adds an overhead of 54 bytes to the original packet. Therefore, to support a standard MTU of 1500 bytes for the inner packet, the outer packet must have an MTU of at least 1554 bytes. However, VMware recommends adding an extra buffer of 146 bytes to account for possible additional headers or VLAN tags. Therefore, the minimum MTU size for the UPLINK profile is 1700 bytes (1554 + 146). References: : VMware NSX-T Data Center Installation Guide, page 23. : VMware NSX-T Data Center Administration Guide, page 102. : VMware NSX-T Data Center Installation Guide, page 24.

What are two functions of the Service Engines in NSX Advanced Load Balancer? (Choose two.)

1. A. It collects real-time analytics from application traffic flows.
2. B. It stores the configuration and policies related to load-balancing services.
3. C. It performs application load-balancing operations.
4. D. It deploys web servers to perform load-balancing operations.
5. E. It provides a user interface to perform configuration and management tasks.

Correct Answer: CE
The Service Engines in NSX Advanced Load Balancer are VM-based applications that handle all data plane operations by receiving and executing instructions from the Controller. The Service Engines perform the following functions:
They perform application load-balancing operations for all client- and server-facing network interactions. They support various load-balancing algorithms, health monitors, SSL termination, and persistence profiles.
They provide a user interface to perform configuration and management tasks. The user interface is accessible through a web browser or a REST API. The user interface allows the user to create and modify virtual services, pools, health monitors, policies, analytics, and other load-balancing settings
https://docs.vmware.com/en/VMware-Telco-Cloud-Platform/3.0/vmware-telco-cloud-reference-architecture-gui

Where in the NSX UI would an administrator set the time attribute for a time-based Gateway Firewall rule?

1. A. The option to set time-based rule is a clock Icon in the rule.
2. B. The option to set time based rule is a field in the rule Itself.
3. C. There Is no option in the NSX U
4. D. It must be done via command line interface.
5. E. The option to set time-based rule is a clock Icon in the policy.

Correct Answer: D
According to the VMware documentation1, the clock icon appears on the firewall policy section that you want to have a time window. By clicking the clock icon, you can create or select a time window that applies to all the rules in that policy section. The other options are incorrect because they either do not exist or are not related to the time-based rule feature. There is no option to set a time-based rule in the rule itself, as it is a policy-level setting. There is also an option to set a time-based rule in the NSX UI, so it does not require using the command line interface.
https://docs.vmware.com/en/VMware-NSX/4.1/administration/GUID-8572496E-A60E-48C3-A016-4A081AC8

An administrator has deployed 10 Edge Transport Nodes in their NSX Environment, but has forgotten to specify an NTP server during the deployment.
What is the efficient way to add an NTP server to all 10 Edge Transport Nodes?

1. A. Use Transport Node Profile
2. B. Use the CU on each Edge Node
3. C. Use a Node Profile
4. D. Use a PowerCU script

Correct Answer: C
A node profile is a configuration template that can be applied to multiple NSX Edge nodes or transport nodes at once. A node profile can include settings such as NTP server, DNS server, syslog server, and so on1. By using a node profile, an administrator can efficiently configure or update the network settings of multiple NSX Edge nodes or transport nodes in a single operation2. The other options are incorrect because they are either not efficient or not supported. Using the CLI on each Edge node would require manual and repetitive commands for each node, which is not efficient. Using a Transport Node Profile would not work, because a Transport Node Profile is used to configure the NSX-T Data Center components on a transport node, such as the transport zone, the N-VDS, and the uplink profiles3. Using a PowerCLI script might work, but it would require writing and testing a custom script, which is not as efficient as using a built-in feature like a node profile.
https://docs.vmware.com/en/VMware-NSX/4.1/administration/GUID-B4AE1432-690E-480E-91C4-903C1E549